0 Doble sistema de fijación – Dual installation system– Double système de fixation – Два способа крепления Instalación con adhesivo Installation with adhesive Pose par adhésif Клеевое крепление 1 1 2 2 3 4 4 Pri er rimer Primer Primer Limpia a superficie de montaje con un5rl5a so-Apretar el tubo “primer”6para romper la cáp- Aplicar7una fina capa de “primer” sobre la8superfi-Pegar el adhesivo en el soporte a pared. lución de agua y alcohol al 50 %. sula interna hasta queel líquido empape elcie del soporte y sobre la pared para aumentar laAffix the adhesive onto the wall support . Clean the mounting surface with a 50/50 wa- tapón. adherencia y dejarlo actuar 5 minutos. Collez l’adhésif sur le mur. ter/alcohol solution. Bend the primer to break the internal capsule Apply a thin layer of primer onto the support andПриложите базовую часть с клеем к Nettoyez la surface de montage avec un1 1e so- and wait until the liquid2soaks into the cap. the43ll to increase adherence and leawa v4e for 5 lution à 50 % eau-alcool. Appuyez sur le tube « primer » pour briser minutes. креплению и зафиксируйте. Очистите поверхность для монтажа спир-la capsule interne jusqu’à ce que liquide im-Appliquez une fine couche de « primer » sur la товым раствором с водой 50/50. prègne le bouchon. Primer surface du support et sur le mur pour augmenteriP remr Согнитеклеевой карандаш Primer, чтобыl’adhérence et laisser agir pendant 5 min. жидкость из внутренней защитной капсу-Тонким слоем нанесите клеевой состав Primer лы вытекла и распределилась по корпусу.на место крепежа на стене и основу крепления и оставьте на 5 минут, это увеличит склеивание. 5 5 6 6 87 8 8 Presionar el adhesivo fuertemente durante Ensamblar el soporte sobre el accesorio y retirar laColocar el accesorio en la pared desde la parteDespués de 72 horas, ensamblar nuevamen- 30”. protección del adhesivo. No tocar con los dedos.inferior, retirar el artículo y presionar durante 30”.te el artículo al soporte de pared. Press the adhesive vigorously for 30 seconds.Mount the support onto the accessory and remo-Place the accessory on the wall from the bottom,Leave to set for 72 hours and them remount Pressez fortement pendant 30 secondes.ve the protection from the adhesive. Do not touchremove the article and press for 30 seconds.the article onto the wallsupport. Прижмите с силой крепление к базовойwith your fingers. Positionnez l’accessoire sur le mur en com-Après 72 heures, assemblez de nouveau части и подержите 30 секунд. Assemblez le support sur l’adhésif et retirez lamençant par le bas, retirez l’article et pressez pen-l’article sur son support mural. feuille protectrice de l’adhésif. Ne touchez pas ladant 30 secondes. Оставьте крепление на стене на 72 часа, surface adhésive avec les doigts. Поместите крепление аксессуара на стену,затем прикрепите основную часть аксес- Уберите защитную часть с клеевого покрытия,прижмите и держите в течение 30 секунд. суара. не дотрагивайтесь руками. Instalación con taladro Drilled installation Pose par perçage Установка с помощью дрели 1 1 1 2 3 2 3 3 4 4 4 PPrriieerrPPrimimeerrrriieerPPrriimmeer r